Nokia 4A0-220 Nokia GMPLS-Controlled Optical Networks Exam Practice Test

The equipment vendor is not a parameter that is considered when restoring an LSP. Restoration is the process of re-establishing an LSP after a failure by using an alternative path that meets the same constraints as the original LSP. The parameters that are considered when restoring an LSP include coloring, reservation priority, maximum latency, bandwidth, protection type, and other QoS attributes. The equipment vendor does not affect the restoration process as long as the nodes support GMPLS protocols and interoperate with each other. References : RFC 4427 - Recovery (Protection and Restoration) Terminology for Generalized Multi-Protocol Label Switching (GMPLS), [Nokia GMPLS-controlled Optical Networks Course | Nokia]

Test Mode is a feature of the Link Management Protocol (LMP) that allows testing the connectivity and functionality of a link or a TE-link. Test Mode can be initiated by either end of a link or a TE-link by sending a Test Message with a Test ID and a Test Pattern. The Test Message is sent over the control channel of the link or the TE-link and contains information such as the source and destination IP addresses, the link ID, and the test parameters. The receiving node then verifies the Test Message and sends back a TestStatusAck message with the same Test ID and Test Pattern. The TestStatusAck message indicates whether the test was successful or not, and if not, what was the reason for failure. Test Mode can be used to check if a link or a TE-link is operational, if it has any errors or faults, or if it supports certain features or capabilities. References : Nokia GMPLS-controlled Optical Networks Course | Nokia, RFC 4204 - Link Management Protocol (LMP)

The label on the top of the MPLS label stack is swapped at an intermediate node. This is because the top label is the one that is visible to the node and determines the forwarding decision. The node looks up the top label in its label forwarding table and swaps it with a new label that corresponds to the next hop or destination. The node then forwards the packet to the next node, which repeats the same process. The bottom label is only used to indicate the end of the label stack and is not swapped. References : [Nokia GMPLS-controlled Optical Networks Course | Nokia], [MPLS Label Stack - Nokia]

A network with ROADM GMPLS nodes and optical transponder connections could have both L0 and L1 restoration capabilities. L0 restoration refers to the ability of the network to recover from failures at the optical layer, such as fiber cuts or node failures, by rerouting the affected LSPs to alternative paths at the same layer. L0 restoration can be achieved by using GMPLS signaling protocols, such as RSVP-TE or CR-LDP, to establish backup LSPs in advance or on demand. L0 restoration can provide fast recovery times and high availability for optical services34. L1 restoration refers to the ability of the network to recover from failures at the sub-wavelength layer, such as transponder failures or wavelength unavailability, by rerouting the affected LSPs to alternative paths at a higher layer. L1 restoration can be achieved by using GMPLS routing protocols, such as OSPF-TE or ISIS-TE, to advertise the sub-wavelength information and availability to other nodes in the network. L1 restoration can provide more flexibility and efficiency for sub-wavelength services56. References:

• 3: GMPLS - Nokia
• 4: Generalized Multi-Protocol Label Switching - Wikipedia
• 5: Sub-Wavelength Switching - Nokia
• 6: Sub-Wavelength Switching in Optical Networks - IEEE Xplore

The Link Maintenance window is a feature of NFM-T that allows the user to perform maintenance tasks on links and nodes in a GMPLS network. The Link Maintenance window is a wizard that provides commands to set links and nodes to maintenance mode, which prevents them from being used for routing new LSPs or carrying traffic. The user can also use the Link Maintenance window to reroute existing LSPs away from the links and nodes that are in maintenance mode, either manually or automatically. The Link Maintenance window helps the user to perform network maintenance operations without disrupting the service availability or quality12. References:

• 1: Nokia GMPLS-controlled Optical Networks Course | Nokia
• 2: Nokia Network Functions Manager for Transport User Guide | Nokia

The 3R resource is a type of optical regeneration resource that can be used to extend the reach of optical signals in a GMPLS-controlled optical network. The 3R resource performs three functions: reshaping, retiming, and reamplifying the optical signal. The 3R resource can be added to the Network Planning Application (NPA) in the Nokia Network Functions Manager for Transport (NFM-T) through the Constraint Wizard. The Constraint Wizard is a tool that allows the user to define various constraints and parameters for the network design, such as optical impairments, wavelength availability, protection schemes, and regeneration resources. The user can select the 3R resource from the list of available resources and specify its location, capacity, and cost. The NPA then uses this information to perform feasibility checks and path computation for the LSP requests12. References:

• 1: Nokia GMPLS-controlled Optical Networks Course | Nokia
• 2: Nokia Network Functions Manager for Transport User Guide | Nokia

The GMRE functionality is guaranteed in Nokia equipment by controller redundancy. The controller is the hardware component that runs the GMPLS software and controls the switching fabric of the node. Each node has two controllers, one active and one standby, that synchronize their states and databases. If the active controller fails, the standby controller takes over and ensures the continuity of the GMRE functionality. References : Nokia GMPLS-controlled Optical Networks Course | Nokia, 1830 Photonic Service Switch (PSS) | Nokia

The GMRE node address is the IP address for communication between network elements (NEs) in a GMPLS-controlled optical network. The GMRE node address is also known as the GMRE loopback address or the GMPLS node IP. It is used by GMPLS protocols such as LMP and RSVP to identify and communicate with other GMRE nodes. The GMRE node address is configured on each NE and is advertised by OSPF-TE to other nodes in the same area. References : Nokia 1830 PSS-4, PSS-8, PSS-16 and PSS-32 Platforms - NATO, 1830 PSS Identifiers

GMPLS stands for Generalized Multi-Protocol Label Switching, which is a protocol suite that extends MPLS to control different types of switching technologies, such as optical, TDM, and packet switching1. The meaning of Generalized in GMPLS is that it can be used for traffic types other than data packets, such as wavelengths, time slots, or fibers2. GMPLS can also use implicit labels that are derived from the physical properties of the data stream, such as wavelength or timeslot, instead of explicit labels that are carried in the packet header3. This allows GMPLS to support various transport networks and applications, such as optical transport networks (OTN), wavelength switched optical networks (WSON), and automatic switched optical networks (ASON)4. References:

• 1: Nokia GMPLS-controlled Optical Networks Course | Nokia
• 2: What is MPLS and GMPLS? - Metaswitch
• 3: Generalized Multi-Protocol Label Switching - Wikipedia
• 4: GMPLS - Nokia

A Nominal Route in a GMPLS network is the optimal path that meets the Traffic Engineering (TE) constraints for a given LSP request. A Nominal Route is calculated by the NFM-T using the Constrained Shortest Path First (CSPF) algorithm, which takes into account parameters such as bandwidth, latency, priority, protection type, and other QoS attributes. A Nominal Route is stored in the NFM-T database and can be used to provision LSPs over the network. A Nominal Route can differ from the Current Route, which is the actual path that the LSP is taking at a given time, due to network changes or failures. References : Nokia GMPLS-controlled Optical Networks Course | Nokia, Nokia Advanced Optical Network Management with NFM-T Course | Nokia

Automation is one of the key features of GMPLS that allows dynamic provisioning of optical transport connections between IP routers and optical network elements2. Automation reduces the operational time and administrative overhead required to provision new connectivity, which in turn reduces the operational expenditure (OPEX) of the network. Reducing CAPEX, providing resilience against multiple failures, and supporting multi-vendor networks are not direct benefits of automation, but rather possible outcomes of using GMPLS in general. References:

• 1: Nokia GMPLS-controlled Optical Networks Course | Nokia
• 2: GMPLS - Nokia
• 3: Traffic survivability through Protection and Restoration Combined (PRC) - YouTube
• [4]: GMPLS: Architecture and Applications - Google Books

The Soft Shutting Down state in the NFM-T is an administrative maintenance state where services stay up but no new traffic can be routed over the TE-link. This state is used to prepare a TE-link for maintenance or decommissioning without affecting the existing services. The NFM-T sets the TE-link to Soft Shutting Down state by sending a Notify message with the Administrative State Change flag to the head-end node of the TE-link. The head-end node then stops accepting new LSP requests over the TE-link and sends a PathErr message with the Administrative State Change flag to all the tail-end nodes of the LSPs in the TE-link. The tail-end nodes then stop sending new traffic over the LSPs and send a ResvErr message with the Administrative State Change flag to all the intermediate nodes of the LSPs. The intermediate nodes then update their routing tables and stop forwarding new traffic over the LSPs. The existing traffic, however, continues to flow over the LSPs until they are manually deleted or rerouted by the NFM-T. References : Nokia GMPLS-controlled Optical Networks Course | Nokia, Nokia Advanced Optical Network Management with NFM-T Course | Nokia