Labour Day Special Limited Time 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: suredis

Examstrust Logo
examstrust mcafee
  1. Home
  2. HP
  3. HPE Technical Certification
  4. HPE0-S59 - HPE Compute Solutions

HP HPE0-S59 HPE Compute Solutions Exam Practice Test

Page: 1 / 6
Total 60 questions
Get HPE0-S59 Full Access Download HPE0-S59 PDF

HPE Compute Solutions Questions and Answers

PDF + Testing Engine

  • Product Type: PDF + Testing Engine
$59.5  $169.99
Add to Cart

Testing Engine

  • Product Type: Testing Engine
$42  $119.99
Add to Cart

PDF Study Guide

  • Product Type: PDF Study Guide
$36.75  $104.99
Add to Cart
Question 1

In the past a customer experienced a networking issue where network ports went down and came back up in quick succession.

Which HPE Virtual Connect SE 100 GD F32 Module for HPE Synergy feature can be configured to disable such ports?

Options:

A.

Pause flood protection

B.

sFlow

C.

Storm control

D.

Port flap protection

Question 2

Refer to the exhibit.

Which statement about this logical JBOD is true?

Options:

A.

This logical JBOD can be connected to multiple systems to formulate a snared datastore.

B.

After deleting this logical JBOD drives will he blocked for 12h m case this JBOD must be re-created

C.

After deleting this logical JBOD, its drives w not be available until a clean-up procedure 6 done

D.

This logical JBOD can be presented to the compute nodes in a different frame.

Question 3

You need to setup HPE Synergy frames after hardware components are discovered within HPE OneView.

Put the steps to achieve this goal into the coned order in the answer area on the right.

Options:

Question 4

An administrator tries to open iLO interlace from HPE OneView Instead of being automatically logged in a login prompt displays

Where should you start the troubleshooting process?

Options:

A.

At the iLO interface to verify whether the ILO Advanced license is properly applied

B.

At HPE OneView Interface to verify whether the server is In the maintenance mode

C.

At the iLO interface to verify whether the SSO certificate is removed from an iLO.

D.

At HPE OneView Interface to verify whether the iLO processor is disabled

Question 5

Which compute node parameters are captured within server hardware type?

Options:

A.

Number of the CPUs

B.

installed operating system

C.

Mezzanine card configuration

D.

Size of the memory Installed

Question 6

You modified a logical interconnect group mat is used to configure logical interconnects in five different logical enclosures. What will be the impact of that change?

Options:

A.

All physical interconnects from affected logical interconnects will be placed in a maintenance mode

B.

All physical interconnects from the affected logical interconnects must he rebooted to activate the new configuration

C.

All logical interconnects configured using this logical Interconnect group will report inconsistency

D.

All logical interconnects configured using this logical interconnect group will be automatically updated

Question 7

Your customer experienced some problems caused by outdated HPE Superdome Flex firmware. Which update method should they use to avoid these issues in the future?

Options:

A.

HPE OneView method for I/O firmware update procedure

B.

RMC CLI to update I/O and HPE Persistent Memory firmware

C.

HPE OneView IT HPE Persistent Memory firmware must be updated.

D.

HPE SUM if HPE Persistent Memory firmware must be updated

Question 8

You plan to configure a Link Aggregation Group (LAG) for two connections within a server profile for a compute node running an ESXI system.

What is required from the VMware side to enable LAG?

Options:

A.

Virtual Distributed Switch

B.

vSphere Standard license

C.

Load balancing cluster

D.

Dedicated VMKernel port

Question 9

Your customer wants to add dedicated Fibre Channel connectivity to the HPE Synergy frame running HPE Synergy 480 Gen10 compute modules, each with one CPU socket populated Currently they use two 12 Gb SAS switches and two HPE Virtual Connect SE 100Gb F32 Modules for HPE Synergy installed in third fabric.

What must be done to enable dedicated FC connectivity for this HPE Synergy frame?

Options:

A.

A second CPU must be installed for all HPE Synergy 480 Gen10 compute nodes.

B.

For Brocade switches, a logical interconnect group must be created in HPE OneView.

C.

For VC-FC modules, all of server facing ports must be property licensed.

D.

SAS switches must be moved to second fabric and FC modules Installed in the first one.

Load More HPE0-S59 Questions
Page: 1 / 6
Total 60 questions
Get HPE0-S59 Full Access Download HPE0-S59 PDF