CWNP CWNA-109 Certified Wireless Network Administrator Exam Practice Test

Wireless bridging is a WLAN technology role that allows two or more networks to be connected wirelessly over a distance. A wireless bridge consists of two or more APs that are configured to operate in bridge mode and use directional antennas to establish a point-to-point or point-to-multipoint link. Wireless bridging can support high data rates and is suitable for scenarios where running cables is impractical or expensive. To create a wireless link between two buildings on a single campus that supports at least 150 Mbps data rates, wireless bridging is an appropriate solution678. References: CWNA-109 Study Guide, Chapter 6: Wireless LAN Devices and Topologies, page 271; CWNA-109 Study Guide, Chapter 6: Wireless LAN Devices and Topologies, page 265; Wi-Fi Wireless Bridging Explained.

DHCP (Dynamic Host Configuration Protocol) is a commonly used method to locate the controllers by the APs in a WLAN that is implemented using wireless controllers. DHCP is a protocol that allows a device to obtain an IP address and other network configuration parameters from a server. In a wireless controller scenario, the APs can use DHCP to request an IP address from a DHCP server, which can also provide the IP address or hostname of the wireless controller as an option in the DHCP response. This way, the APs can discover the wireless controller and establish a connection with it. Alternatively, the APs can also use other methods to locate the wireless controller, such as DNS (Domain Name System), broadcast or multicast discovery, or manual configuration. References: 1, Chapter 8, page 309; 2, Section 5.2

An ACK (Acknowledgement) frame is a short control frame that is sent by the receiver of a data or management frame to confirm that the frame was received correctly. The ACK frame is sent after a SIFS (Short Interframe Space) interval, which is the shortest time gap between frames in 802.11. If the transmitter does not receive an ACK frame within a specified time, it assumes that the frame was not delivered and must be retransmitted. This is part of the 802.11 reliability mechanism that ensures reliable data delivery over an unreliable wireless medium . References: [CWNA-109 Study Guide], Chapter 5: IEEE 802.11 Medium Access, page 209; [CWNA-109 Study Guide], Chapter 5: IEEE 802.11 Medium Access, page 203.

The solution that you recommend is an Overlay WLAN monitoring solution. An Overlay WLAN monitoring solution is a system that uses dedicated sensors or probes to monitor the WLAN performance over time. The sensors are deployed throughout the WLAN coverage area and collect data on various metrics such as signal strength, noise level, channel utilization, interference, throughput, latency, packet loss, and QoS. The sensors send the data to a centralized server or appliance that analyzes the data and provides a single pane of glass for administration and monitoring of the solution. An Overlay WLAN monitoring solution can help to detect and troubleshoot WLAN issues, optimize WLAN performance, and generate reports and alerts. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 538; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 508.

OFDM is a modulation method that divides the channel bandwidth into multiple subcarriers, each carrying a single data symbol. This allows for higher data rates and more robust transmissions in multipath environments. OFDM was first introduced in the 802.11a standard, which operates in the 5 GHz band and supports data rates up to 54 Mbps. Later, the 802.11g standard adopted OFDM for the 2.4 GHz band, and the 802.11n and 802.11ac standards enhanced OFDM with features such as MIMO (Multiple Input Multiple Output), channel bonding, and higher-order modulation schemes to achieve data rates up to 600 Mbps and 6.9 Gbps, respectively. These standards are collectively known as the ERP (Extended Rate PHY), HT (High Throughput), and VHT (Very High Throughput) PHYs . References: [CWNA-109 Study Guide], Chapter 4: Radio Frequency Signal and Antenna Concepts, page 163; [CWNA-109 Study Guide], Chapter 4: Radio Frequency Signal and Antenna Concepts, page 157.

The authentication method that is referenced in the 802.11-2016 and 802.11-2020 specifications and is recommended for robust WLAN client security is 802.1X/EAP. 802.1X/EAP stands for IEEE 802.1X Port-Based Network Access Control with Extensible Authentication Protocol and is a framework that provides strong authentication and dynamic encryption key generation for WLAN clients. 802.1X/EAP involves three parties: the supplicant (the client), the authenticator (the AP or the controller), and the authentication server (usually a RADIUS server). The supplicant sends its credentials (such as username and password, certificate, or token) to the authenticator, which forwards them to the authentication server. The authentication server verifies the credentials and sends a response to the authenticator, which grants or denies access to the supplicant. The authentication server also generates a master key that is used to derive encryption keys for the data frames between the supplicant and the authenticator. 802.1X/EAP supports various EAP methods that offer different levels of security and flexibility, such as EAP-TLS, EAP-PEAP, EAP-TTLS, EAP-FAST, and EAP-SIM. SSL, IPSec, and WEP are not authentication methods, but rather encryption or security protocols that are not specific to WLANs or referenced in the 802.11 specifications. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 299; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 289.

a mesh portal is a device that connects a mesh BSS (MBSS) to an Ethernet network, such as the Internet. A mesh portal acts as a bridge between the wired and wireless domains, and allows the mesh stations to communicate with external networks. A mesh portal is also a mesh point, which means it can forward traffic within the MBSS.

The other options are not correct. Option A. Mesh Gate is a device that connects a mesh BSS (MBSS) to another mesh BSS or another wireless network, such as an infrastructure BSS or an ad hoc network2. A mesh gate acts as a gateway between different wireless domains, and allows the mesh stations to communicate with other wireless networks. A mesh gate is also a mesh point, which means it can forward traffic within the MBSS. Option B. Mesh Switch is not a valid term in the 802.11 standard. Option C. Mesh Router is also not a valid term in the 802.11 standard.

 The cipher suite specified by the 802.11-2016 standard and is not deprecated is Counter Mode with CBC-MAC Protocol (CCMP). CCMP is an encryption protocol that uses Advanced Encryption Standard (AES) as the underlying cipher and provides confidentiality, integrity, and origin authentication for wireless data. CCMP is the mandatory encryption protocol for WPA2 and WPA3. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 295; [IEEE Standard for Information technology–Telecommunications and information exchange between systems Local and metropolitan area networks–Specific requirements - Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications], page 1560.

A POE device that requires 47 W of power should use the 802.3bt specification. This is because 802.3bt is the latest POE standard that supports up to 90 W of power delivery over four pairs of wires in an Ethernet cable. The previous POE standards, such as 802.3af and 802.3at, only support up to 15.4 W and 30 W of power delivery over two pairs of wires in an Ethernet cable, respectively. Therefore, they are not sufficient for powering a device that requires 47 W of power. The 802.11at specification does not exist; it is a typo or confusion with the 802.3at specification. References: CWNA-109 Study Guide, Chapter 8: Wireless LAN Access Points, page 2431

CCI is still a possibility in this network because the client devices connected to one of the channel 1 APs will transmit frames that reach the other channel 1 AP as well as clients connected to the other channel 1 AP. CCI stands for co-channel interference, which is a type of interference that occurs when two or more devices transmit on the same channel within range of each other. CCI reduces performance and capacity because it causes contention and collisions on the wireless medium, which leads to retransmissions and delays. CCI can be mitigated by increasing physical separation between devices using the same channel or by reducing transmit power levels to limit coverage area. In this scenario, three access points are used within a facility. One access point is on channel 11 and the other two are on channel 1. The two access points using channel 1 are on either side of the access point using channel 11 and sufficiently apart so that they do not interfere with each other when they transmit frames. However, this does not prevent CCI from occurring between their client devices that are connected on channel 1. For example, if a client device connected to one of the channel 1 APs sends a frame to another device on the wired network or on another wireless network (such as an Internet server or a VoIP phone), that frame will be heard by both channel 1 APs as well as any other client devices connected to either of them on channel 1. This will cause CCI because these devices will have to wait for the channel to be clear before they can transmit their own frames. The answer that CCI only occurs in the 5 GHz frequency band is incorrect; CCI can occur in any frequency band where devices use the same channel. The answer that channel 11 loops around and causes CCI with channel 1 is also incorrect; channel 11 does not loop around and it operates in a different frequency band than channel 1. References: CWNA-109 Study Guide, Chapter 5: Radio Frequency Signal and Antenna Concepts, page 147

The term used to describe the problem in this configuration is Co-Channel Interference (CCI)1. CCI occurs when multiple access points are on the same or overlapping channels, causing interference and degradation in network performance1. In this case, one AP is on channel 1 and the other is on channel 2, which are overlapping channels, leading to CCI1.

The least expensive solution available for increasing throughput for these users without implementing configuration options that are not recommended is to use a 40 MHz channel on the 5 GHz radio. This solution can double the channel bandwidth and increase the data rates for the 5 GHz capable 802.11ac clients. Using a 40 MHz channel on the 5 GHz radio is also less likely to cause co-channel interference or overlap with other channels than using a 40 MHz channel on the 2.4 GHz radio, which has only three non-overlapping channels. Using a 160 MHz channel on the 5 GHz radio may provide even higher throughput, but it may also consume too much of the available spectrum and cause more interference with other devices or networks. Installing a second AP in the coverage area may also improve the throughput, but it may require additional costs and configuration. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 216; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 206.

VHT stands for Very High Throughput, which is a physical layer (PHY) specification that supports the 5 GHz frequency band and supports 80 MHz channels. VHT is used by the IEEE 802.11ac standard, which is also known as Wi-Fi 5. VHT allows for higher data rates and more spatial streams than the previous HT (High Throughput) PHY, which is used by the IEEE 802.11n standard, also known as Wi-Fi 4. HT supports the 2.4 GHz and 5 GHz bands, but only supports up to 40 MHz channels12

The other options are not correct because:

ERP (option C) stands for Extended Rate PHY, which is a physical layer specification that supports the 2.4 GHz frequency band and supports up to 20 MHz channels. ERP is used by the IEEE 802.11g standard, which is also known as Wi-Fi 3. ERP allows for higher data rates than the previous DSSS (Direct Sequence Spread Spectrum) PHY, which is used by the IEEE 802.11b standard, also known as Wi-Fi 234

OFDM (option D) stands for Orthogonal Frequency Division Multiplexing, which is a modulation technique that divides a signal into multiple subcarriers that are spaced orthogonally to each other. OFDM is not a physical layer specification, but a common feature of many PHY specifications, including ERP, HT, and VHT. OFDM allows for higher spectral efficiency and robustness against multipath interference than the previous CCK (Complementary Code Keying) modulation technique used by DSSS34

 iPerf is an open source tool that is designed to perform a throughput test on the WLAN. iPerf is a cross-platform command-line tool that can measure the bandwidth and quality of network links by generating TCP or UDP traffic between two endpoints. iPerf can run as either a server or a client mode, depending on whether it receives or sends traffic. iPerf can also report various metrics of network performance, such as throughput, jitter, packet loss, delay, and TCP window size. To perform a throughput test on the WLAN using iPerf, one device needs to run iPerf in server mode and another device needs to run iPerf in client mode. The devices need to be connected to the same WLAN network and have their IP addresses configured properly. The device running iPerf in client mode needs to specify the IP address of the device running iPerf in server mode as well as other parameters such as protocol, port number, duration, interval, bandwidth limit, packet size, etc. The device running iPerf in server mode will listen for incoming connections from the client device and send back acknowledgments or responses depending on the protocol used. The device running iPerf in client mode will send traffic to the server device according to the specified parameters and measure the network performance. The device running iPerf in client mode will display the results of the throughput test at the end of the test or at regular intervals during the test. The results can show the average, minimum, maximum, and instantaneous throughput of the network link, as well as other metrics such as jitter, packet loss, delay, and TCP window size. References: 1, Chapter 7, page 287; 2, Section 4.3

The BSSID (Basic Service Set Identifier) is typically mapped to an AP’s MAC address if a single BSS is implemented. The BSSID is a unique identifier that distinguishes one BSS from another within the same RF medium. It is usually derived from the MAC address of the AP’s radio interface, but it can also be manually configured or randomly generated by some vendors. The BSSID is used by client stations to associate with an AP and to send and receive frames within a BSS. References: , Chapter 1, page 24; , Section 1.2

 What you should tell him is that due to 802.11 network operations and the dynamic rates used by devices on the network, the two radios will likely not exceed the 1 Gbps Ethernet link. This is because the actual throughput of an 802.11 network is much lower than the theoretical data rates due to factors such as overhead, contention, interference, retransmissions, and environmental conditions. Moreover, the data rates used by devices on the network vary depending on their distance, signal quality, capabilities, and configuration. Therefore, it is unlikely that both radios of the AP will simultaneously use the maximum data rates and saturate the 1 Gbps Ethernet link. Upgrading to a 10 Gbps Ethernet link or running a second 1 Gbps Ethernet link may be unnecessary and costly. Compressing all data before transmitting it onto the Ethernet link may introduce additional overhead and latency. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 227; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 217.

 The most effective method for testing roaming in relation to 802.11 VoIP handsets is to place a call with the handset and move around the facility to test quality during roaming. This method allows you to evaluate the actual performance and user experience of VoIP calls over wireless networks, as well as identify any potential issues such as signal strength, interference, latency, jitter, packet loss, or handoff delays. A spectrum analyzer can only show you the RF activity during a VoIP call, but not how it affects the voice quality or roaming behavior. A protocol analyzer can capture the traffic generated when a laptop roams, but it cannot simulate the characteristics of a VoIP handset such as battery life, antenna design, codec support, or QoS features. A built-in roaming monitor is not a common feature in all VoIP handsets, and it may not provide accurate or comprehensive information about the roaming process. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 487; [Voice over Wireless LAN 4.1 Design Guide], page 6-19.

A common problem that causes this scenario is captive portal issues. A captive portal is a web page that requires users to authenticate or accept terms and conditions before accessing the Internet through a WLAN. A captive portal is often used for guest networks to provide security and control over the network access. A captive portal works by intercepting the user’s web requests and redirecting them to the portal page until the user completes the required action. However, sometimes the captive portal may not work properly due to various reasons, such as browser settings, firewall rules, DNS configuration, or network errors. This can prevent the user from browsing the Internet or seeing the portal page. To troubleshoot captive portal issues, you can try to use a different browser, clear the browser cache and cookies, disable any VPN or proxy settings, manually enter the portal URL, or contact the network administrator. NTP issues, hardware issues, or IP routing issues are not common problems that cause this scenario. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 343; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 333.

The security option for 802.11 networks that supports SAE and requires protected management frames is WPA3. WPA3 stands for Wi-Fi Protected Access version 3 and is the latest security standard for WLANs. WPA3 supports two modes: WPA3-Personal and WPA3-Enterprise. WPA3-Personal uses Simultaneous Authentication of Equals (SAE) as the key exchange protocol, which provides stronger protection against offline dictionary attacks and password guessing than WPA2-Personal. WPA3 also requires protected management frames, which are encrypted frames that prevent spoofing, replay, or denial-of-service attacks on management frames such as deauthentication or disassociation frames. WPA, WPA2, and OWE do not support SAE or require protected management frames. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 307; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 297.

To calculate the EIRP at the antenna element, we need to add the transmitter output power, subtract the cable loss, and add the antenna gain. All these values need to be converted to dBm first, if they are not already given in that unit. In this case, we have:

Transmitter output power = 50 mW = 10 log (50) dBm = 16.99 dBm Cable loss = 3 dB Antenna gain = 9 dBi

EIRP = Transmitter output power - Cable loss + Antenna gain EIRP = 16.99 - 3 + 9 EIRP = 22.99 dBm

Rounding up to the nearest integer, we get 23 dBm as the EIRP at the antenna element12. References: CWNA-109 Study Guide, Chapter 2: Radio Frequency Fundamentals, page 92; CWNA-109 Study Guide, Chapter 2: Radio Frequency Fundamentals, page 88.

Discovering the scale of the problem is the next logical step in the troubleshooting process after identifying the problem of poor wireless connections on the third floor of a building under your administration. Troubleshooting is a systematic process of finding and resolving problems or issues in a network or a system. Troubleshooting usually follows a general methodology that consists of several steps or phases, such as:

Identifying the problem: This step involves defining and describing the problem clearly and accurately based on the symptoms and evidence observed or reported by users or administrators. For example, in this case, the problem is that three individuals have reported poor wireless connections on the third floor of a building.

Discovering the scale of the problem: This step involves determining how widespread and severe the problem is by gathering more information and data from different sources and perspectives. For example, in this case, this step could involve checking if other users or devices on the third floor or other floors are experiencing similar issues, verifying if there are any changes or updates in the network configuration or environment that could affect the wireless connections, testing if there are any differences in performance or quality between different access points or channels on the third floor, etc.

Performing corrective actions: This step involves applying possible solutions or fixes to resolve or mitigate the problem based on logical reasoning and analysis. For example, in this case, this step could involve adjusting the output power or channel assignment of the access points on the third floor, relocating or reorienting some access points or antennas to improve coverage or reduce interference, updating or replacing some faulty or outdated hardware or software components, etc.

Verifying the solution: This step involves confirming that the problem is solved or improved by testing and monitoring the network performance and user satisfaction after applying corrective actions. For example, in this case, this step could involve measuring and comparing the signal strength and throughput of wireless connections on the third floor before and after performing corrective actions, asking for feedback from users who reported poor wireless connections to see if their issues are resolved or reduced, etc.

Creating a plan of action or escalating the problem: This step involves documenting and reporting the problem and its solution for future reference and improvement purposes. It also involves deciding whether to close or escalate the problem depending on its status and severity. For example, in this case, this step could involve creating a report that summarizes what was done to troubleshoot and fix poor wireless connections on the third floor with relevant data and evidence to support it. It could also involve escalating poor wireless connections to higher-level administrators if they persist or worsen despite performing corrective actions.

VHT TXOP (Very High Throughput Transmit Opportunity) power save is a feature introduced with the 802.11ac amendment, which is designed to improve the power efficiency of devices connected to a WLAN. This feature enhances battery life in several ways, compared to the legacy Power Save mode:

Enhanced Power Saving: VHT TXOP power save allows devices to disable more components of the WLAN transceiver when they are in a low power state. This reduces the power consumption during periods when the device is not actively transmitting or receiving data.

Intelligent Wake-Up Mechanisms: It employs more sophisticated mechanisms for devices to determine when they need to wake up and listen to the channel, further reducing unnecessary power usage.

Optimized Operation: This power save mode is optimized for the high-throughput environment of 802.11ac networks, allowing devices to efficiently manage power while maintaining high performance.

Legacy Power Save mode, introduced in earlier versions of the 802.11 standards, does not provide the same level of component disablement or the intelligent wake-up mechanisms found in VHT TXOP power save, making option B the correct answer.

OFDMA is a new modulation scheme introduced in 802.11ax that allows multiple users to share the same channel by dividing it into smaller subchannels called resource units (RUs). This improves the efficiency and capacity of the WLAN by reducing contention and overhead. However, to use OFDMA, both the AP and the client must support 802.11ax and negotiate the parameters of the subchannel allocation. Therefore, the customer needs to upgrade the clients that require OFDMA to 802.11ax devices12.

The other options are not correct because they do not reflect the reality of OFDMA. Option B is incorrect because OFDMA is a mandatory feature of 802.11ax for both downlink and uplink transmissions, and all 802.11ax APs must support it1. Option C is incorrect because OFDM and OFDMA are different modulation schemes, and OFDM does not allow multiple users to share the same channel. Option D is incorrect because 802.11ac devices cannot support OFDMA through driver upgrades, as they lack the hardware and firmware capabilities to do so2.

The client drivers are faulty and should be upgraded is the likely problem for the laptop that can see and connect to 2.4 GHz APs, but does not even see 5 GHz APs. The client drivers are the software components that enable the wireless adapter of the laptop to communicate with the operating system and the network. The client drivers are responsible for scanning the available wireless channels, detecting and connecting to the access points, negotiating the security and data rate parameters, and transmitting and receiving data frames. If the client drivers are faulty, outdated, or incompatible, they may cause various issues with the wireless performance and functionality, such as low data rates, poor signal strength, frequent disconnections, or inability to see or connect to certain access points or channels.

One of the possible causes of faulty client drivers is that they do not support or recognize some of the features or standards of the 802.11ac technology, such as wider channel bandwidths, higher modulation schemes, or DFS (Dynamic Frequency Selection) channels. This could explain why the laptop can see and connect to 2.4 GHz APs, but not 5 GHz APs, as 802.11ac operates only in the 5 GHz band and uses channels that are wider (up to 160 MHz) and higher (up to channel 165) than those used by previous standards. Moreover, some of the 5 GHz channels are subject to DFS rules, which require the access points and client stations to monitor and avoid using channels that are occupied by radar systems or other primary users. If the client drivers do not support or comply with DFS rules, they may not be able to see or connect to access points that use DFS channels.

To solve this problem, the client drivers should be upgraded to the latest version that supports and is compatible with 802.11ac features and standards. This can be done by downloading and installing the updated driver software from the manufacturer’s website or using a device manager tool. Upgrading the client drivers may also improve other aspects of wireless performance and functionality, such as data rates, signal strength, security, and stability. References: 1, Chapter 12, page 493; 2, Section 8.1

The channel that can be used for VHT transmissions according to the 802.11 specification is channel 144. VHT stands for Very High Throughput and is the PHY layer specification for 802.11ac devices. VHT transmissions can use channel bandwidths of 20 MHz, 40 MHz, 80 MHz, or 160 MHz in the 5 GHz band. Channel 144 is one of the channels in the 5 GHz band that can support VHT transmissions with any of these bandwidths. Channel 6, channel 1, and channel 11 are channels in the 2.4 GHz band that cannot support VHT transmissions, as they are only compatible with legacy (802.11b/g/n), HT (802.11n), or ERP (802.11g) transmissions with up to 20 MHz bandwidth. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 214; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 204.

Impedance is the measure of opposition to the flow of alternating current (AC) in a circuit. Impedance mismatch occurs when the impedance of the radio does not match the impedance of the antenna or the cable. This causes some of the transmitted or received signal to be reflected back, resulting in a loss of power and efficiency. The voltage standing wave ratio (VSWR) is a metric that indicates the amount of impedance mismatch in a transmission line. A higher VSWR means a higher impedance mismatch and a lower signal quality. A VSWR of 1:1 is ideal, meaning there is no impedance mismatch and no reflected power. A VSWR of 2:1 means that for every 2 units of forward power, there is 1 unit of reflected power12.

The other options are not correct because they do not affect the VSWR in RF cables. A high gain yagi antenna or a high gain parabolic dish antenna can increase the signal strength and directionality, but they do not cause impedance mismatch in the cable. Radio output power above 100 mW but below 400 mW is within the acceptable range for most WLAN devices and does not cause excessive VSWR in the cable3.

The feature of 802.11ax (HE) that provides this functionality is OFDMA. OFDMA stands for Orthogonal Frequency Division Multiple Access and is a technology that allows multiple devices to communicate simultaneously on the same channel in the same BSS. OFDMA works by dividing a channel into smaller subchannels called Resource Units (RUs), which are composed of groups of subcarriers or tones. Each RU can be assigned to a different device based on its bandwidth requirement and signal quality. This way, OFDMA can increase the efficiency and capacity of the channel by reducing overhead, contention, and latency. OFDMA can also support both uplink and downlink multi-user transmissions using trigger frames and buffer status reports. 6 GHz support, TWT, and Wi-Fi-LTE are not features of 802.11ax that provide this functionality. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 226; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 216.

The statement that in modern networks, both centralized and distributed data forwarding work well for most standard office deployments is true about WLAN performance. Data forwarding refers to how wireless frames are transmitted from wireless clients to wired networks or vice versa through wireless access points (APs). Centralized data forwarding means that all wireless frames are sent to a central controller or gateway before being forwarded to their destinations. Distributed data forwarding means that wireless frames are forwarded directly by the APs to their destinations without going through a central controller or gateway. Both methods have their advantages and disadvantages, depending on the network size, topology, traffic pattern, security, and management requirements. However, in modern networks, both methods can achieve high performance and scalability for most standard office deployments, as they can leverage advanced features such as fast roaming, load balancing, quality of service, and encryption. The other statements about WLAN performance are false. In most WLANs, special skill or tuning is required to get peak performance, such as selecting the appropriate channel, power, data rate, and antenna settings. WLANs perform worse as more wireless clients connect with each AP, as they cause more contention and interference on the wireless medium. To get the best performance out of an AP, you should not disable data rates of 72 Mbps and lower, as they are needed for backward compatibility and range extension. References: CWNA-109 Study Guide, Chapter 9: Wireless LAN Architecture, page 2811

The FCS (Frame Check Sequence) is appended to the end of each 802.11 data frame after the payload. The FCS is a 4-byte field that contains a CRC-32 (Cyclic Redundancy Check) value that is calculated based on the contents of the MAC header and the payload of the frame. The FCS is used by the receiver to verify the integrity of the frame and to detect any errors or corruption that may have occurred during transmission. If the FCS does not match with the expected value, the frame is discarded by the receiver. References: , Chapter 4, page 139; , Section 4.2

The RF energy that exists in the environment from intentional and unintentional RF radiators that forms the baseline above which the intentional signal of your WLAN must exist is the best explanation of the noise floor noted in the report. The noise floor is a term that describes the level of background noise or interference in a wireless channel or band. The noise floor is measured in dBm (decibel-milliwatts) and it represents the minimum signal strength that can be detected or received by a wireless device. The noise floor is influenced by various factors, such as the sensitivity of the receiver, the antenna gain, the cable loss, and the ambient RF environment. The ambient RF environment consists of intentional and unintentional RF radiators that emit RF energy in the wireless spectrum. Intentional RF radiators are devices that are designed to transmit RF signals for communication purposes, such as Wi-Fi access points, Bluetooth devices, microwave ovens, or cordless phones. Unintentional RF radiators are devices that are not designed to transmit RF signals but generate electromagnetic radiation as a by-product of their operation, such as USB 3 devices, PC power supplies, or fluorescent lights. The noise floor affects WLAN performance and quality because it determines the minimum signal-to-noise ratio (SNR) that is required for a successful wireless transmission. SNR is the difference between the signal strength of the desired signal and the noise floor of the channel. SNR is also measured in dB and it indicates how much the signal stands out from the noise. A higher SNR means a better signal quality and a lower bit error rate. A lower SNR means a worse signal quality and a higher bit error rate. Therefore, to achieve a reliable WLAN connection, the intentional signal of your WLAN must exist above the noise floor by a certain margin that depends on the data rate and modulation scheme used. The other options are not accurate or complete explanations of the noise floor noted in the report. The noise caused by elevators, microwave ovens, and video transmitters is not the noise floor but rather examples of interference sources that contribute to the noise floor. The extra energy radiated by access points and client devices beyond that intended for the signal is not the noise floor but rather an example of spurious emissions that cause interference to other devices or channels. The energy radiated by flooring materials that causes interference in the 2.4 GHz and 5 GHz bands is not the noise floor but rather an example of attenuation or reflection that reduces or changes the direction of the signal. References: CWNA-109 Study Guide, Chapter 5: Radio Frequency Signal and Antenna Concepts, page 139

The factors that will have the most significant impact on the amount of wireless bandwidth available to each station within a BSS are:

The number of client stations associated to the BSS

The presence of co-located (10m away) access points on non-overlapping channels

The number of client stations associated to the BSS affects the wireless bandwidth because each station shares the same channel and medium with other stations in the same BSS. The more stations there are, the more contention and collision there will be for the channel access, which reduces the throughput and efficiency of the wireless communication. The wireless bandwidth available to each station depends on how the access point allocates the channel resources and how the stations use the channel time. For example, if the access point uses a round-robin scheduling algorithm, each station will get an equal share of the channel time regardless of its data rate or traffic demand. However, if the access point uses a proportional fair scheduling algorithm, each station will get a share of the channel time that is proportional to its data rate and traffic demand, which may result in higher or lower bandwidth for different stations.

The presence of co-located (10m away) access points on non-overlapping channels affects the wireless bandwidth because even though they use different channels, they may still cause interference and noise to each other due to channel leakage or imperfect filtering. The interference and noise can degrade the signal quality and SNR of the wireless communication, which reduces the data rate and throughput of the wireless communication. The wireless bandwidth available to each station depends on how well the access point and the station can cope with the interference and noise from other channels. For example, if the access point and the station support dynamic frequency selection (DFS) or adaptive radio management (ARM), they can switch to a less congested channel or adjust their output power or antenna gain to avoid or minimize interference from other channels.

Return loss is a measure of how well the components of an RF system are matched in terms of their impedance. Impedance is the opposition to the flow of alternating current in a circuit, and it depends on the frequency, resistance, capacitance, and inductance of the components. When the impedance of the source, the transmission line, and the load are not equal, some of the power is reflected back to the source, causing a loss of forward power. This loss is expressed in decibels (dB) as return loss. The higher the return loss, the lower the reflection and the better the impedance matching. Conversely, the lower the return loss, the higher the reflection and the worse the impedance matching.

VSWR (Voltage Standing Wave Ratio) is another way of expressing the same concept. It is the ratio of the maximum voltage to the minimum voltage along a transmission line due to the interference of the incident and reflected waves. A VSWR of 1:1 means that there is no reflection and perfect impedance matching. A VSWR higher than 1:1 means that there is some reflection and impedance mismatch. The higher the VSWR, the higher the reflection and the lower the return loss.

Therefore, a significant impedance mismatch between components in an RF system will cause high reflection, high VSWR, and low return loss.

 A Wi-Fi scanner is a basic tool that can be used to easily locate areas of high co-channel interference. A Wi-Fi scanner is a software application that can run on a laptop, tablet, smartphone, or other device that has a Wi-Fi adapter. A Wi-Fi scanner can scan the wireless environment and display information about the detected access points and client stations, such as their SSID, BSSID, channel, signal strength, security, and data rate. A Wi-Fi scanner can also show the channel utilization and overlap of different access points, which can indicate the level of co-channel interference. Co-channel interference is a type of interference that occurs when multiple access points use the same or adjacent channels within the same coverage area. Co-channel interference can reduce the throughput and performance of the WLAN, as the access points and client stations have to contend for the channel access and avoid collisions. To identify areas of high co-channel interference, a Wi-Fi scanner can be used to measure the signal strength and channel utilization of different access points and compare them with a threshold or a baseline. Alternatively, a Wi-Fi scanner can also use a color-coded heat map to visualize the co-channel interference level in different locations. References: 1, Chapter 7, page 279; 2, Section 4.3

Based on the information given, what can be determined as certainly true about this AP is that it has 4 radio chains. A radio chain is a hardware component that consists of an antenna, a radio frequency (RF) amplifier, and a transceiver. The number of radio chains indicates how many spatial streams an AP can transmit or receive simultaneously using Multiple Input Multiple Output (MIMO) technology. The notation x:y:z in an AP specification denotes the number of radio chains (x), the number of spatial streams (y), and the number of spatial streams per band (z). Therefore, a tri-band, 4x4:4, Wi-Fi 6, 802.11ax AP has four radio chains in each of its three bands (2.4 GHz, low 5 GHz, and high 5 GHz). It also supports four spatial streams in total and four spatial streams per band. It cannot be determined as certainly true that it supports four channels in each band, UL-MU-MIMO, or uses a modified OpenWRT firmware based on the information given. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 223; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-109], page 213.

In the 802.11ax (High Efficiency, HE) amendment, one of the key features introduced is BSS (Basic Service Set) Coloring. This feature is designed to mitigate issues arising from overlapping BSSs (OBSS), which can lead to contention and interference in dense wireless environments. BSS Coloring works by:

Assigning a "color" (a small number) to each BSS: This helps devices differentiate between frames from their own BSS and those from neighboring BSSs.

Reducing Inter-BSS Interference: Devices can ignore frames from different BSSs (with a different "color") under certain conditions, reducing the impact of OBSS interference.

Improving Spatial Reuse: By distinguishing between transmissions from different BSSs, devices can make more informed decisions about when to transmit, improving the efficiency of spatial reuse and reducing unnecessary contention.

This feature directly impacts design decisions related to AP placement and the spacing between same-channel BSS cells, as it allows for closer placement of APs on the same channel without significantly increasing interference, thus improving overall network capacity and efficiency.

The other options, while features of 802.11ax, do not directly pertain to reducing overlapping BSS contention in the same manner:

TWT (Target Wake Time) optimizes device sleep schedules to conserve power.

Uplink MU-MIMO enhances uplink data transmission capabilities but doesn't specifically address OBSS contention.

6 GHz Band Support introduces new spectrum for Wi-Fi use but is not a feature aimed at reducing OBSS contention within the 802.11ax framework.

Therefore, the correct answer is B, BSS Color.